tangency

英

美

网络  切线连续; 接触; 相切; 切向参考; 切矢连续

复数：tangencies　

英英释义

noun

• (electronics) a junction where things (as two electrical conductors) touch or are in physical contact
  1. they forget to solder the contacts
  Synonym:contact
• the state of being tangent

双语例句

• Concepts about bridge node and loop tangency are proposed. The principle of the loop shrinkage of the signal flow graphs is deduced from the point of view of the equivalence of node split.
  提出了桥结点、环路相切概念，从结点分裂的等价观点出发，导出了信号流图中环路收缩的原理。
• Through square and triangular permutation ways of cutting identical dimension on steel plate, the first model of computational combinatorics is set up by tangency permutation method.
  模型Ⅰ主要用“相切排列法”通过“方形排列”及“三角形排列”两种情形建立了在一块固定尺寸钢板上切割一种规格小圆板的组合计算模型；
• The optimal allocation of the certainty and severity of penalty under the cost restrain is the point of tangency of the curve of equal deterrence and the curve of equal cost of deterrence.
  成本约束下的刑罚确定性与严厉性的最优配置是等威慑水平曲线与等威慑支出曲线的切点。
• Taking the reform in curriculum system, content of courses and teaching method as our point of tangency;
  以课程体系、教学内容和教学方法的改革为切入点，大力加强传统专业的更新改造；
• Their point of tangency is called the pitch point, and since it lies on the line of centers, it is the only point at which the tooth profiles have pure rolling contact.
  大小齿轮的接触点称为节点，由于节点位于中心线上，因此节点是齿形轮廓线上唯一做纯滚动接触的点。
• Tangency is controlled by the first two control points from a surface boundary, assuming that these points lie in one line.
  相切是由曲面边界的最初两个控制点控制的（假设这些点在一条线上）。
• The paper takes teaching environment as point of tangency, gives an thorough analysis on the constructing element of teaching environment and educational equipment as well as their mutual relations.
  教育技术装备是教育体系中不可或缺的重要组成部分，是发展大教育的要素之一，也是推动教育信息化的重要力量。
• Emergency Solution to the Equipment Failure of Subnet Access Node in Tangency SDH Loop
  相切组网SDH子网接入点失效的应急方案
• Given a NURBS curve, perturbation for control points is chosen and the LSM ( Least Square Method) is used to modify the geometric features such as position, tangency or curvature of the selected parametric point on the given curve.
  通过对NURBS曲线的控制顶点扰动，采用最小二乘法修改曲线上给定一点处的位置、切矢和曲率等几何特征，并讨论了多点几何特征同时修改的情况。
• The essence of arc joining is making the tangency of the arc and line or the arc and arc. The programmed Drawing method of arc joining based on AutoCAD secondary-development is studied in this article. The Visual LISP drawing program of arc joining is merited.
  圆弧连接的本质就是使圆弧与直线或圆弧与圆弧相切，在此研究了基于AutoCAD二次开发的圆弧连接程序化绘制方法，用VISUALLISP语言编程建立了圆弧连接通用绘图程序。